Legacy Car Audio Car Stereo System LCD18M User Manual

INSTRUCTION MANUAL  
THEFT DETERRENT DETACHABLE SYSTEM  
AUTO-LOADING DISC CD / MP3 PLAYER  
WITH ELECTRONIC ANTI-SHOCK FUNCTION  
AM/FM STEREO 2 BAND TUNING RADIO  
MODEL:LCD18M  
LOCATION AND FUNCTION OF CONTROLS  
INSTALLATION METHOD  
This is an anti-theft installation method.  
The main unit wears a METAL MOUNTING SLEEVE.  
Please connect the wiring, eg, the Power supply, the Speakers and the Antenna  
according to the requirements of this Instruction Manual, then install the  
metal mounting sleeve into the car as per the diagram illustrated below.  
Bend the tabs on the mounting  
sleeve against the dashboard  
with a screwdriver.  
To raise the anti-skip capability of the unit,  
please ensure the metal support strap is  
connected firmly to the car chassis.  
METAL SUPPORT STRAP  
1,2 & 3.SEL(MENU) BUTTON AND VOLUME UP ( + )/ DN ( - ) BUTTONS  
a) Press the SEL button briefly, it is activated as selecting each mode of E. VOL  
-> VOLUME ->BASS ->TREBLE -> BALANCE -> FADER ->  
When selecting a desired audio mode, press the + and - button to adjust the  
audio effect.  
UNIT CHASSIS  
PLASTIC TRIM RING  
DASHBOARD  
METAL MOUNTING SLEEVE  
FRONT PANEL  
In each mode, the waiting time is about 5 seconds, and the time waiting time  
is over, it returns to the last display mode of tuner or CDP mode.  
The control mode of E.VOL is operated with following numeric display.  
- VOL: (MIN)00, 01,......49, 50(MAX).  
To remove the CD player out of the mounting sleeve,  
insert the two supplied keys into the left and right side  
slots of the chassis at the same time.  
Then pull the chassis out of the mounting sleeve as  
shown in the illustration.  
- BASS/TREB: -10, -9,...,0,...9,10  
- BAL: 10L, 9L,...,L=R,...9R,10R  
- FAD: 10F,9F,...,F=R,...9R,10R  
To remove the plastic trim ring out of the unit chassis, please grasp the upside  
of left and right two sides of the plastic trim ring and pull it up a little firstly, then  
draw it out. Or grasp the upside of one side of the plastic trim ring and pull it up  
a little, and draw it outward, then grasp the other side and pull it up a little and  
draw it outward.  
b) When pressed longer 2 seconds, it is activated as cyclical mode of following  
functions for user s selection.  
-> DSP(OFF/ FLAT/ POP M/ROCK/CLASSICS) ->BEEP (2ND/ALL/OFF) ->  
VOL LAST/VOL ADJ -> ESP 10 seconds/40 seconds mode.  
After selecting the desired mode, press the + and - button to select one setup  
item of the desired mode.  
NOTE  
BEEP 2ND, BEEP ALL, BEEP OFF MODE  
The situation of beep sound is selected. The 3 mode is selected as also the  
+ or - button.  
Remove the two screws that protect  
the CD player during transportation  
before operating the player.  
Before installing and operating  
the CD player, remove the metal  
mounting sleeve illustrated by the  
arrows.  
To attach the removable faceplate, insert the  
right side of the faceplate into the right of the  
CD player chassis first. Then push the left side  
of the faceplate into the chassis until you hear  
- BEEP 2ND mode:  
it click  
.
The beep is only generated when an allotted double key is pressed long (2  
second).  
- BEEP ALL mode:  
The beep is generated when any key is pressed.  
- BEEP OFF mode:  
The beep sound is disabled.  
VOL LAST/VOL ADJ  
You can select VOL LAST or VOL ADJ mode by using the + and - button.  
VOL LAST: The radio switches on at the actual volume it had when it was last  
switched off.  
VOL ADJ: After pressing SEL button, you can pre-select a constant switch-on  
volume by using the + and - button.  
Page 9  
Page 2  
ESP 10 seconds/40 seconds:  
IN ESP mode, you can select 10 seconds or 40 seconds electronic shockproof  
mode by using the + and - button.  
WIRING DIAGRAM  
ANTENNA PLUG  
4. POWER ON/OFF  
Turn the device on by using any button except the REL button, EJECT key and  
TUNING knob on the front panel; and the LCD will display WELCOME. It can  
also turn on this device to insert a disc into the CD slot with label surface up.  
Press power button and hold for approximately 1 second to turn power off; and  
the LCD will display GOOD BYE.  
FUSE 7A  
YELLOW  
CONSTANT B+  
RED R  
WHITE  
RCA OUTPUT LINE  
BLACK(GND)  
L
5. LCD DISPLAY  
6. CD SLOT  
FUSE 0.5A  
WHITE  
IGNITION SWITCH  
RED (B+)  
FUSE 0.5A  
GRAY  
BLUE AUTO ANT  
+
FRONT  
+
FRONT  
7&8. CD TRACK UP / DOWN AND CD FF/REW BUTTONS  
Whilst in CD/MP3 mode, press the >>| button briefly to play next track.  
Press the |<< button briefly to play the previous track.  
Press the >>| or |<< button and hold to skip forwards or backwards, release to  
resume disc playback.  
-
WHITE/BLACK  
GREEN  
GRAY/BLACK  
VIOLET  
-
LEFT  
RIGHT  
LOUDSPEAKER  
LOUDSPEAKER  
+
+
REAR  
REAR  
GREEN/BLACK  
VIOLET/BLACK  
-
-
Note:  
9. INTRO ON/OFF BUTTON  
In CD/MP3 playback process, press the INT button briefly to activate the CD  
track scan mode.  
Whilst INTRO is on, it begins playing the first 10 second section of each song,  
until the last song is played. It stops the CD track scanning and begins playing  
the selected track when the INT button is pressed again.  
1. Make sure you use a speaker with 4 ohm load impedance  
2. Make sure the auto antenna wire does not come into contact with the vehicle  
chassis.  
C AU TIO N :  
In o rd e r to p ro te c t p o w e r IC fro m b e in g b urn t o u t d u rin g in s ta lla tio n th e c a r s te re o ,  
it is n e c e s s a ry to follo w the s te p s b e low to c o nn e c t the w ire s d u ring in s ta lla tion :  
10. TOP/ BUTTON  
In CD/MP3 playback process, press the TOP/ button to pause the CD play-  
back, press again to resume normal playback.  
First song will be played when the TOP/ button is pressed for longer than 1  
second during CD/MP3 playback.  
S te p 1 : C o n n e c t th e g ro u n d w ire (B la c k );  
S te p 2 : C o n n e c t a ll s p e a ke r w ire s a n d p o w e r a n te n n a w ire (B lu e ):  
Le ft s p e a ke r  
Rig h t s p e a ke r  
Fro n t s p e a ke r: W h ite (+ ) W h ite /B la c k (- )  
Re a r s p e a ke r: G re e n (+ ) G re e n /B la c k (- )  
S te p 3 : RC A Lin e O u t (R- R e d / L- W h it e ).  
G ra y (+ )  
Vio le t (+ )  
G ra y/B la c k (- )  
Vio le t/B la c k (- )  
11. CD EJECT BUTTON  
The loaded CD can be ejected by pressing the EJECT button. If the CD is left  
in the CD slot after ejection, it will reload the CD after 8 seconds.  
S te p 4 : C o n n e c t Ba c k u p (Ye llo w ) a nd Ac c w ire (R e d )  
12. MUTE ON/OFF BUTTON  
This button serves to switch the MUTED state on/off.  
Press the MUTE button to suppress the loudspeaker temporarily, and press  
again to resume listening. The muted state will be also released when the  
MODE, BAND, SEL and the + and - button on the front panel is pressed.  
13. MODE BUTTON  
When a disc is present in the CD slot, pressing the MODE button will allow you  
to change to RADIO mode (and back). The LCD display information changes  
with the mode (please note: when no disc is present in the unit, this button does  
not provide a function).  
Page 3  
Page 8  
14. TUNING CONTROL  
Rotate this control at radio mode to select your desired radio broadcasting  
station. The selected frequency will appear on the LCD display.  
TROUBLE SHOOTING  
15. BAND BUTTON  
Before using the check list please make all the connections first.  
If you still have questions after going through the checklist, please consult  
your local customer service representative.  
In radio mode, press the BAND button for AM or FM reception.  
The character of the selected band will be visible on the display.  
In CD/MP3 format-mixed disc playback mode, long press BND button, it will  
change from CD mode to MP3 mode(the defaulted mode is CD).  
This BAND button as a search function during MP3 playback:  
During MP3 mode:  
PROBLEM  
CAUSE  
SOLUTION  
Press the BAND button short, it is activated as cyclical selecting song mode as  
following: -> TRACK SERIAL NUMBER SEARCH -> THE FIRST CHARACTER  
SEARCH -> DIRECTORY SEARCH  
1) In TRACK SERIAL NUMBER SEARCH selecting song mode, the MP3 T 000  
will be visible on the LCD display and the hundreds digit 0 that the MP3 disc  
contain will flash.  
Press the + or - button to select and enter the number on the flashing digit  
place from 1 to 9.  
Then press the SEL button to confirm the entered number and the 0 on the  
tens digit will be flashing.  
Press the + or - button to select and enter the number on the flashing digit  
from 1 to 9.  
Then press the SEL button to confirm the entered number and the 0 on the  
units place digit will be flashing.  
Press the + or - button to select and enter the number on the flashing digit  
If the power supply is properly  
connected to the car, switch the  
ignition key to " ACC "  
The car ignition is not on.  
The fuse is blown  
No power  
Replace the fuse  
Another CD is present in the Remove CD in the player, then insert  
player  
a new one with label face up  
Disc incorrectly inserted  
upside-down  
Insert the CD with label face up  
Disc cannot  
be loaded or  
ejected  
CD is extremely dirty or  
defective  
Clean the CD or try a different CD  
Temperature inside the car is  
too high  
Give enough time for the temper-  
ature in the vehicle to cool down.  
from 1 to 9.  
After finishing enter all the number of the song serial number on the flashing  
digit, press the SEL button to play the corresponding track.  
2)In the FIRST CHARACTER SEARCH selecting song mode, the A--......, will  
be visible on the LCD display. (If there are files names its first character are  
A, the......is the first file name its first character is A by the order of A~Z and  
0~9; otherwise, the ......is NONE.)  
Press the + or - button to select files that the first character by the order of  
A~Z and 0~9.  
Then press the >>| or |<< button to select one file its first character is the  
selected one. Finally press the SEL button to play the selected file.  
3) In DIRECTORY SEARCH selecting song mode, the root folder will be visible  
on the LCD display. (If there is not a root folder in the current MP3 disc, you  
will find a root named ROOT.)  
Condensation  
Turn off the player for at least an  
hour, then try again.  
Volume is too low  
Adjust volume to desired level  
No sound  
Wiring is not properly  
connected  
Check the wiring connection  
The installation angle is more Adjust the installation angle to less  
than 30 degrees  
than 30 degrees  
Sound skips  
CD is extremely dirty or  
defective  
Clean the CD or try a different CD  
Then press the + or - button to select a desired folder.  
And then press the >>| or |<< button to select a desired track in the folder.  
Finally press the SEL button to play the selected track.  
The radio does  
not work  
The antenna cable is not  
connected  
Insert the antenna cable firmly  
16&17. +10 AND LOC/-10 BUTTON  
During the normal playback of CDs in MP3 format:  
Press +10 and LOC/-10 button to move up and down10 tracks at a time.  
When the remained total tracks is lack of 10, the both buttons are inactively.  
During RADIO mode, press the LOC/-10 button to change local reception or  
distance reception. (Note: This operation is for FM reception only)  
Page 7  
Page 4  
18. DISP BUTTON  
In MP3 playback process, press this DISP button repeatedly to display as  
follows: TRACK NUMBER=>ELAPSED TIME=>REAL TIME=>TRACK NAME.  
In RADIO mode, press the DISP button once to display frequency or the real  
time.  
The time will appear on the display, when the DISP button is pressed for 2 secs.  
The time flashes, you can then adjust HOUR and MINUTE by pressing the +  
and - button, respectively.  
PRECAUTION OF DISC PLAY:  
Cleaning the CD:  
Before playing a CD, wipe it off with a clean, dust-free cleaning cloth.  
Wipe the disc in the direction of the arrow.  
19. RELEASE BUTTON  
To remove the front control panel from the main body, press the REL button.  
Always insert the CD with the label side facing upwards.  
If the CD is inserted with the printed side facing downwards, the device may be  
damaged.  
PRECAUTIONS AND MAINTENANCE  
Note: If there is already a CD in the CD slot, do not try to insert a second CD.  
This may damage the device.  
Always hold CDs by the edge. In order to keep the CD clean do not touch the surface.  
Pull out the CD as shown below.  
CAUTION: Do not install the detachable panel before connecting the wire.  
1. The unit is designed for negative terminal of the battery which is connected to the vehicle metal.  
Please confirm it before installation.  
2. During the radio or CD mode, if you drop the front panel, the unit will automatically turned off.  
3. If the car interior is extremely hot, as after being parked in the sun, do not use the player until the  
car has been driven for a while to cool off the interior.  
4. Store the detachable in its protective case for safe keeping.  
5. To drop/take away/install and recover front panel, see under the illustration.  
Do not attach any sticker or adhesive tape on the CD.  
Do not expose the CD to direct sunlight or sources of heat such as heating vents.  
Do not leave CDs in a car if it is parked in direct sunlight as that will lead to a con-  
siderable rise in the temperature inside the car.  
PROTECTIVE CASE  
FRONT PANEL  
FRONT PANEL  
Note: Do not use any solvents such as petrol or thinning agents.  
Commercially available cleaning substances or antistatic spray. This will damage  
the device.  
RELEASE BUTTON  
RELEASE BUTTON  
FRONT PANEL  
Page 5  
Page 6  

KWC Musical Instrument Amplifier Z534171000 User Manual
Life Fitness Home Gym SU55 User Manual
Lightolier Indoor Furnishings VPA2G29PR232 User Manual
Logitech Computer Keyboard 920 000383 User Manual
Lucent Technologies Laptop MN102H75K User Manual
Mace Security Camera CAM91 User Manual
Manitowoc Ice Ice Maker 7622073 User Manual
Maytag Microwave Oven W10188238A User Manual
MGE UPS Systems Power Supply FlexPDU 12 IEC User Manual
Micro Technic Power Supply PV 5127 User Manual