PYLE Audio Car Video System PLVS420 User Manual

INSTRUCTION MANUAL  
IN DASH COLOR TT-LCDMONITOR  
PLVS420  
4 INCH SUNVISOR TFT-LCD MONITOR  
 
OPERATION  
1.Connect the monitor power input plug to a DC power source  
(Red plug +12 VDC, Black plug(-) to ground).  
2.Connect the external video source output signal (from VCD,  
DVD, TV etc.) To the VIDEO in jack.  
3.Press power button to turn the monitor on and off. The backlight  
for the button will turn brighter.  
4.Press the menu button to activate the picture display characteristics  
adjustment.  
5.Press the + button to increase the selected adjustment level or  
press the - button to decrease the level.  
6.Press V1/V2 button to switch between two video signals.  
 
INSTALLATION  
Installation will vary from vehicle to vehicle, as headrests in  
vehicles are not standard.  
 
PRECAUTION  
To prevent short-circuiting of the electrical system and cause  
serious damage to the unit or the vehicle, you are advised to  
follow the instructions carefully.  
Should there be requirement to replace blown fuse, do  
remember to disconnect all power supply and switch  
the unit before replacing it with a new one. Use only correct  
rating fuse to avoid damaging the unit.  
During operation, if there is symptom of over-heating or  
system mal-function,do switch off the unit and consult your  
dealer immediately. Please do not attempt to open up the  
unit since there is no serviceable parts inside.  
Do not drop the LCD display panel or subject it to direct  
impact.  
If the LCD panel is broken, do avoid all human contact  
to the broken glasses or fluid leaked out from the enclosure.  
If come into contact ,do flush and clean affected areas with  
plenty of water. Seek medical attention immediately.  
The battery life of the remote control unit is about six months  
long. To ensure effective control, please replace the batteries  
regularly.  
Do not use any chemical solvent, cleaning agent or corrosive  
detergent to clean away dirt on the surface of the screen.  
By doing so, you may cause irreversible damage to the surface  
of the TFT screen. To clean off dirt or finger prints, use a soft  
damp lens cleaning cloth.  
When operating the display unit, avoid touching or pressing  
the LCD glass panel Excessive force may cause irreparable  
damage to the LCD screen.  
Ensure no metal or foreign materials are dropped in between  
the display screen and enclosure. Obstacles may impeach  
smooth running of the tray and may cause electrical shocks.  
 
FRONT PANEL  
1.power indicator  
2.power On/Off  
3.menu  
1
2
3
4
5
6
7
4.positive adjustment  
5.negative adjustment  
6.menu select up  
7.menu select down  
8.IR  
8
9
9.video input  
REMOTE CONTROL  
1.menu  
2.power on/off  
3.game -  
4.game +  
MENU  
ON/OFF  
GAME  
1
3
2
5.volume -  
6.volume +  
7.sleep  
4
VOLUME  
GAME  
5
6
MUTE  
SLEEP  
DISPLY  
8.game  
7
9
9.mute switch  
10.display mode  
PICTURE  
RECALL  
10  
12  
11.image up/down/left/right reverse  
12.factory default setting  
REMOTE CONTROL  
 
Technical Specification  
Screen size:  
System:  
4 inch(Diagonal length)  
PAL & NTSC  
Display Method:  
Resolution:  
Power supply:  
TFT active matrix system  
390x282 dots  
DC 12V  
Power consumption: 8W  
Dimension: 210 X129 X 30mm  
WIRING  
Black:power input  
Yellow:video 1 input  
 
 

Philips GPS Receiver Bluetooth QuickStart Kit User Manual
Philips Home Theater System HTL2101 User Manual
Philips Network Card CRA01 00 User Manual
Philips Window SA2300 User Manual
Pioneer DVR DVR 103 User Manual
Planar Car Video System PL2210W User Manual
Polaroid Digital Camera PDC 3000 User Manual
Polycom Cordless Telephone 14171914 HD User Manual
Poulan Trimmer RTE113 User Manual
PYLE Audio Car Stereo System PLTDN70 User Manual